Tool Aid

Our Newest Products
	13840, GREAT BIG HOOKER, JR. Special hook design for easy removal of cotter pins and radiator hoses. Great for working in confined areas. Use for pushing and pulling applications. 11” overall length with 6” exposed shaft.
	14950, IMPACT DRIVER SET Use to loosen and tighten screws, nuts and bolts Special handle reduces risk of injury when striking driver with hammer Includes 8 standard and long length interchangeable bits Driver is easily reversible for tightening applications
	15060, TITANIUM MULTI-STEP DRILL For sheet metal and other thin materials up to 1/8” thick. Has 13 hole sizes in 1/32” increments from 1/8” thru 1/2”. High speed steel with titanium coating for longer life. No slip shank fits all 1/4” drills.
	18929, DIE SET FOR SPARK PLUG TERMINALS For 8.0mm and 8.5mm spiral core spark plug wire: Strips the insulation. Crimps the spiral core to the spark plug terminal. Crimps the terminal to the spark plug wire insulation. For use with our Cat. Nos. 18920 and 18930, Ratcheting Terminal Crimping Tools.
	19400, RIVET TOOL FOR PLASTIC RIVETS Sets most plastic rivets in one stroke without re-gripping. Long reach design accessed areas not accessible with lever type tools. Sets all sizes using a single nosepiece. One hand operation.
	32100, ELECTRONIC STETHOSCOPE Will assist in finding unwanted noises such as air and water leaks, bearing noises, squeaks and rattles, faulty lifters, valve knocks and other sounds. Highly sensitive electronic circuitry Microphone at end of 8” flexible shaft
	34729, EXTENSION HOSE FOR DIESEL COMPRESSION Makes for easier diesel compression testing in areas with restricted clearance. Attaches between Cat. No. 34700, Diesel Compression Tester and Tool Aid brand diesel test adapters.
	35400, DIESEL TESTER ADAPTER FOR VOLKSWAGEN TURBO DIRECT INJECTION (TDI) ENGINES 10mm-1.00 thread to test through glow plug port. For ALH and BEW series engines. Hose easily connects to adapter to make testing easier in restricted areas.
	35500, DIESEL TESTER ADAPTER FOR 8MM KUBOTA ENGINES 8mm-1.00 thread to test through glow plug port.
	35550, DIESEL TESTER ADAPTER FOR 10MM KUBOTA ENGINES 10mm-1.25 thread to test through glow plug port on various Kubota engines. Also for: Toyota and Nissan 2.2L, 2 and 3 cylinder Mitsubishi and Ford Escort 2.0L..
	63000, THE STRUTTER™2, MACPHERSON STRUT COIL SPRING TOOL With acme threads and economically priced. Quickly and easily work on the MacPherson Struts found on virtually all modern domestic and imported vehicles. Features a one piece cold headed bolt made of chromium molybdenum alloy steel. The nuts are Grade 5. Use with impact wrench or hand tool ON or OFF the car. Contains complete instructions and safety kit.
	65100, TIRE INFLATOR WITH GAGE Easy to read nylon pop up gage measures from 10 to 120 PSI in 2 PSI increments Weatherproof body with corrosion resistant brass valve Chrome plated dual head chuck on 12” hose 1/4” NPT Female air inlet
	65200, WHEEL WEIGHT TOOL For the easy installation and removal of wheel weights. High impact plastic hammer face protects the wheel and the weight. The removal end has a shield to protect the wheel when the weight is removed. Tightens the wheel weight clip. For use on alloy and chrome wheels.
	82350, DOOR ALIGNER TOOL Align car and truck doors with either bolted or welded hinges in seconds by using leverage. Patented feature pulls door against tool to prevent distorting the metal around latches. Quickly and easily mounts in place with no special tools. Curved handle allows access in restricted areas. Includes special pin for truck doors.
*Our Hottest Tools*
	13820, BIG HOOKER SET Excellent for the removal of radiator hoses from inlets, outlets and clamps; Great for the removal of radiator hoses from inlets, outlets and clamps; Excellent for cotter pin removal; Use on body clips moldings and windshield seals; Retrieve small parts; Remove "O" rings and washers Consists of Cat. Nos. 13800, Extra Long Hooker (OAL 8") and 13810, Great Big Hooker (OAL 15")
	13850, UNIVERSAL HOOK & PICK SET Excellent general purpose set. 7 Different and distinct plated hooks and picks with high impact plastic handles. Longer picks are 8 1/2” overall length and shorter picks are 5 1/4” overall length.
	14270, 3 PIECE BRASS DRIFT PIN SET Contains 3 sizes of drift pin style brass punches: 1/2” x 7”, 5/8” x 7” and 3/4” x 8”. Softer brass will not mar harder metal surfaces. Non-Sparking Knurled handles for better gripping.
	14290, 4 PIECE BRASS PIN PUNCH SET Contains 4 sizes of drift pin style brass punches: 1/8” x 4”, 3/16” x 4”, 1/4” x 4” and 3/8” x 6”. Softer brass will not mar harder metal surfaces. Non-sparking. Knurled handles for better gripping.
	14300, MIGHTY CUTTER Makes accurate, straight cuts with clean edges on rubber or plastic hose, PVC pipe and certain types of wire and wire cable Handles up to 1 1/8" O.D. material For automotive, autobody, marine and aviation shop.
	14800, DOUBLE FLARING TOOL KIT Flares 5 sizes of copper, aluminum, soft steel and brass tubing: 3/16”, 1/4”, 5/16”, 3/8” and 1/2”. For double or single flares up to 45°
	14850, MINI TUBING CUTTER Cuts thin-wall steel, plastic, copper and brass tubing from 1/8” – 5/8” O.D. (3-22mm). Products smooth, clean cut. Compact size allows use in restricted areas. All metal construction.
	14860, TUBING BENDER Bends 3/16”, 1/4”, 5/16” and 3/8” O.D. tubing without kinking or collapsing. Just place tubing in groove and pull the handle to the desired angle. Contoured handle with grip.
	15600, TAPE MEASURE The 1” wide metal blade is two color with a 25’/7.5m dual scale graduated every 1/16” – 1mm. Two way locking feature – slide lock holds blade in position or side button holds blade temporarily from retracting. Cushion cover provides non-slip grip and impact resistance. Case has belt hook and is bright yellow for high visibility.
	17050, GRIME SCRUB BRUSH Makes it easy to clean up after dirty jobs. Gentle and effective cleaning action quickly removes grime from hands. Special row of stiff bristles cleans under fingernails. Contoured handle for firm gripping.
	17280, SPRAY GUN CLEANING KIT Contains all the necessary brushes and tools to effectively clean spray guns including HVLP paint spray guns. Can be used to clean gravity feed, siphon and undercoating guns. Brushes are used to clean threads, air passages and recesses of gun body. Safe to use with chemicals and solvents.
	17370, BUCKET OF EASY GRIP BRUSHES Contains 12 each of the most popular brushes – brass, nylon and stainless steel bristles. For use with cleaning solvents, thinners and chemicals. Each brush is 3 x 7 rows with a hang-up hole in the polypropylene handle. Overall length of each brush is 7”.
	17500, PAIL PUMP Fits all 5 and 6 gallon pails Easily dispenses non-corrosive liquids with lift action Seals designed for use with thinner.
	17550, DRUM PUMP Fully adjustable suction tube fits 15, 30 & 55 gallon drums Lift action handle dispenses approximately 1-1/2 pints per complete stroke Use to transfer petroleum based fluids such as lubricants, anti-freeze, solvents, thinner and other non-corrosive liquids (Not for use with water).
	18500, SPARK PLUG CLEANER Cleans any size spark plug quickly and effortlessly with internally controlled abrasive blasting Uses ordinary air line pressure (Recommended air line pressure is 70-80 PSI) Lever valve on outside of unit allows for blasting with abrasive/air mix or air only.
	18900, PROFESSIONAL RATCHETING TERMINAL CRIMPER Crimps 10-22 gage wire Ratcheting action ensures a perfect crimp every time Eliminates damaged or distorted terminals.
	18920, RATCHETING TERMINAL CRIMPING KIT Versatile kit includes 5 dies for virtually all uses. Die sets quickly interchange for a wide range of applications. Crimping Tool has a steel frame with contoured grips.
	18930, RATCHETING TERMINAL CRIPMER FOR WEATHERPACK TERMINALS For most Weatherpack terminals and non insulated open barrel connectors 22-10 AWG. Ensures a perfect crimp every time. Steel frame with contoured grips. Contains 12 each of the most popular brushes – brass, nylon and stainless steel bristles.
i	18950, WIRE STRIPPER, CUTTER AND TERMINAL CRIMPER Automatically self-adjusts to strip solid or stranded 10-26 gage wires. Removes insulation without damaging the conductor. Crimps insulated and non-insulated terminals. Steel construction with insulated plastic handles.
	19000, WIRE STRIPPER Automatically adjusts to wire size Cuts and strips solid or stranded 12-22 gage wire Handles single or multiple conductor wire Easy to use - yields clean, nick-free results every time
	19250, 1/4" SUPER DUTY RIVETER Sets five sizes of aluminum and steel rivets: 1/8", 5/32", 3/16", 7/32" and 1/4" 2-1/4" nose reach All metal construction, simple design and few moving parts ensure years of hard working use.
	19270, 1/4" SUPER DUTY RIVETER WITH EXTENDED NOSE Sets five sizes of aluminum and steel rivets: 1/8", 5/32", 3/16", 7/32" and 1/4" 5-3/4" nose reach to access deep recesses such as grilles, bumpers and window regulators All metal construction, simple design and few moving parts ensure years of hard working use.
	19600, WHEEL STEP Use these portable "steps" to access hard to reach places like engine compartments, van roofs and truck tops. Fits 14" - 20" tire to provide added height. Will adjust to three positions vertically. Folds for storage.
	19750, HOSE CLAMP PLIERS SET One cross slotted jaw pliers and one wide flat band hose clamp pliers for most ring type and flat band type hose clamps. Jaws rotate to access hose clamps from any angle and to provide better gripping action. Ratcheting locking mechanism holds clamps in open position for easy removal and installation. For use with cleaning solvents, thinners and chemicals.
	23900, IN-LINE SPARK CHECKER Connects in-line between the spark plug and the ignition wire. Use to quickly troubleshoot ignition system with "hands-free" operation. Technician can visually check condition of ignition system at each cylinder. Frequency and intensity of flash indicates whether there is an ignition system problem or a fault in the fuel delivery system.
	23950, COIL ON PLUG IGNITION SPARK CHECKER A quick way to troubleshoot the contemporary “coil on plug” ignition systems found on General Motors, Chrysler, Ford and import vehicles. Flashing bulb indicates ignition or fuel delivery problem. Quickly plugs into boot on coil then clips to ground. Shows a duplicate view of the ignition spark so technician can visually check condition of ignition system at each cylinder. Frequency and intensity of flash indicates whether there is an ignition system problem or fault in the fuel delivery system.
	24800, AUTOMOTIVE DIGITAL MULTIMETER Computer safe - 10 MegaOhm input impedance. Test Volts, Ohms, Amps, Tach, Dwell and Diodes. Combines all the features desired by professional technicians and do-it-yourselfers.
	26200, WIRE AND CABLE TIES ASSORTMENT Ideal for securing wires, harnesses, cables and components. Self locking, flexible, multi-purpose ties made from Nylon 6/6. UL approved. 750 Pieces assortment includes the most popular lengths in different colors: 400 - 4" 18 lbs. tensile strength (100 each white, black, yellow and red ties) 300 - 8" 75 lbs. tensile strength (white ties) 50 - 11" 75 lbs. tensile strength (white ties)
	27000, HEAVY DUTY CIRCUIT TESTER The best quality electrical circuit tester available for checking 6 and 12 volt systems. 5' of tough, flexible, heavily insulated rubber wire is retained in spring supported strain relief designed to withstand the most rugged use. Bulb is easily replaced. Combines all the features desired by professional technicians and do-it-yourselfers.
	27200, HEAVY DUTY CIRCUIT TESTER WITH RETRACTABLE WIRE Features an extra long wire that stretches up to 12 feet for use, then automatically retracts Great for use on cars, trucks, boats, trails, motorcycles, airplanes and snowmobiles A heavy duty ground clip with insulator is on one end of the retractable wire and a spring supported strain relief is on the other For 6 and 12 volt vehicles
	28100, COMPUTER SAFE AUTOMOTIVE LOGIC PROBE Our most computer safe circuit tester! High impedance - the current draw is less than 7 milliamps Quickly and safely tests high and low voltages (power and ground) on all vehicle circuits, including computerized engine and body controls Dual color LED indicates red for power (high) and green for ground (low) on 6, 12 and 24 volt systems.
	31800, SEAL PULLER Use to remove oil and grease seals on cars, SUV’s and light trucks. Has 2 sizes of hook tips to fit most applications. Just insert the tip of the hook behind the seal and use leverage to remove. Each brush is 3 x 7 rows with a hang-up hole in the polypropylene handle. Overall length of each brush is 7”.
	34010, COMPRESSION TEST ADAPTER FOR FORD TRITON ENGINE For use on Ford 3 valve Triton engines as found on the 2004 5.4L Ford F-150 and 2005 4.6L Ford Mustang Adapter has 16mm-1.5 male threads to fit spark plug hole Screws on the 14mm-1.25 male thread at the end of the hose adapter Has 5/8” hex to make installation and removal easier
	34580, AUTOMATIC TRANSMISSION AND ENGINE OIL PRESSURE TESTER WITH TWO GAGES IN MOLDED PLASTIC STORAGE CASE Check oil pressure in automatic transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks including late models. Includes 6' of oil proof hose and 10 assorted fittings.
	34650, POWER STEERING TESTER Gives fast, accurate power steering analysis. Test for defects in power steering pumps, gears and lines. Supplied with 13 adapters. Gage reads from 0-2,000 PSI and 0-140 BAR.
	34900, DIESEL ENGINE COMPRESSION TESTER SET Consists of five of the most popular diesel adapters for testing a wide variety of vehicles including Audi, small Cummins, Ford/International, GM, Mercedes Benz, Volkswagen and Volvo. Optional adapters available for other applications.
	36300, NOID LIGHT SET Quickly, easily and economically test electronic fuel injection signals. Supplied with lights to check GM TBI, Bosch PFI, Ford TBI, GM PFI, Geo TBI and GM SCPI. Easy to use - just disconnect the wiring to the fuel injectors, install the Noid Light into the injector wiring harness and crank or start the engine to view the light pattern.
	36310, ELECTRONIC FUEL INJECTION AND IGNITION SPARK TESTER KIT Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes Cat. No. 23900, In-Line Ignition Spark Checker and Cat. No. 36300, Noid Light Set.
	36330, NOID LIGHTS, IAC TEST LIGHTS & IGNITION SPARK TESTER KIT Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Includes: 8 Noid Lights for checking GM PFI, Ford TBI, GEO TBI, Bosch PFI, GM TBI, GM SCPI, Bosch 2 and GM Multec 2. 2 IAC Test Lights for straight and 90° applications. Cat. No. 23900, Inline Ignition Spark Checker. Quickly diagnose “no start” and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines.
	38000, COMPREHENSIVE FUEL INJECTION PRESSURE TEST KIT Tests gasoline fuel injection pressure systems on virtually all domestic and imported cars and trucks. For multi-port, throttle body and C.I.S. K-Jetronic Fuel Injection Systems. A great value for automotive technicians. Bleed off valve with 6' of translucent hose safely depressurizes system after completion of testing. Includes two gages with dual ranges: 0-100 PSI (0-7 BAR) and 0-50 PSI (0-3.5 BAR).
	56200, MULTI-PORT FUEL INJECTION PRESSURE TESTER SYSTEM WITH QUICK COUPLERS Tests the gasoline fuel pressure on virtually all domestic and foreign vehicles equipped with Multi-port fuel injection. Includes: Adapter for large Schrader valves. Adapter for Ford Multi-port (EFI) and throttle body systems. Adapter for Honda vehicles. 4 piece Banjo Bolt Adapter Set. Assorted hoses, fittings and clamps to test older vehicles. 2 1/2” diameter gage with hang-up hook with dual scale – 100 PSI and 7 BAR. Bleed-off valve and 6’ hose to safely depressurize system after completion of test.
	58000, UNIVERSAL MASTER FUEL INJECTION PRESSURE TEST KIT WITH QUICK COUPLERS Quick coupler fittings provide easy and fast hook-ups. For Multi-port, Throttle Body (TBI) and Continuous Injection Systems (CIS). Tests virtually all domestic and imported cars and trucks with gasoline fuel injection systems. Includes two gages with dual ranges: 1-100 PSI (0-7 BAR) and 0-50 PSI (0-3.5 BAR). Bleed off valve with 6’ of translucent hose safely depressurizes system after completion of testing.
	58050, FUEL INJECTION CLEANING KIT FOR USE WITH AEROSOL CANS For use with most aerosol cleaning cans with 7/16”-28 thread. Valve allows for controlled fluid delivery. Use in combination with optional fuel injection pressure testing adapters. For aerosol cans with .418-20 thread, use optional Cat. No. 58070 adapter that threads into the Cat. No. 58050.
	58100, FUEL INJECTION CLEANING CANISTER WITH 2 GAGES Features two gages. The bottom gage checks the vehicle’s fuel pressure and the top gage is used to set the cleaning pressure. Uses shop air supply and readily available canister cleaning solutions. 20 oz. capacity canister. Includes hanging chain with hook for under the hood attachment. Use in combination with optional fuel injection pressure testing adapters.
	58150, FUEL INJECTION CLEANING KIT FOR USE WITH AEROSOL CANS The perfect starter kit. Comes complete with two adapters to connect to the fuel rail on the most popular vehicles: Cat. No. 53850, Small Schrader Valve Test Adapter for Ford Cat. No. 53908, Large Schrader Valve Test Adapter for GM & Chrysler For use with most aerosol cleaning cans with 7/16-28 thread. Valve allows for controlled fluid delivery. Features quick coupling fittings.
	61800, STRUT ALIGNMENT LEVEL Use this level to restore a vehicle's camber setting after strut repair or installation. Allows technician or customer to safely drive the vehicle before a more precise wheel alignment can be performed. Super strong magnet - mounts on brake rotor, spindle or steering knuckle. Easy to use: (1)Place on vehicle before repair and zero the level. (2)Tighten the wing nut. (3)After the repair, push or pull on the strut until the level returns to the zero position.
	62900, STRUTTER, MacPHERSON STRUT COIL SPRING TOOL For use on the MacPherson Strut Assembly found on virtually all modern domestic and imported vehicles. Use with impact wrench or hand tool, ON or OFF the car. Sells for a fraction of other types. Do not use on GM "A", "C", "J" or "X" Body cars.
	66400, STEERING WHEEL HOLDER AND PEDAL DEPRESSOR Holds the steering wheel, brake pedal, accelerator or clutch pedal in a desired position. Saves time and money by eliminating the need for two technicians to do one job. Easy to assemble, install and release – components slide into position. As a Steering Wheel Holder, use to: hold the steering wheel for toe-in/toe-out work and center the steering wheel. As a Pedal Depressor, use for: tune-ups, brake jobs, fuel injection cleaning, alternator testing, clutch work, engine diagnosis, setting RPM speed, air conditioning work and cylinder balance tests.
	81100, THE SLUGGER IN A TOOL BOX An assortment of the most widely used Slugger pulling and pushing attachments packed in a handy metal box 10 lb. Slide weight designed for in-line impact Quick assembly for applied hook-ups on fender edges, bumper ends, rocker panels, aligning doors and door edges, hoods and hood hinges, trunk and trunk hinges, headlights and many more applications.
	85800, PORTABLE WORKBENCH Designed to hold large parts such as bumpers, hoods, doors, fenders and glass Can be moved easily and adjusted to desired height or width Made of strong tubular steel with thick foam padding to protect painted parts and glass from being scratched Capacity rating of 500 lbs.
	87250, ECONOMY HEAT GUN High performance, hot air source that delivers concentrated, heated air to the job. Use in autobody, automotive, industrial, marine, home, farm and numerous other applications. Has two heat selections: 750 F and 1,000 F. Operates on 120 volts, 10 amps, 1200 watts.
	87460, WINDSHIELD REMOVAL KIT This kit contains the basic tools and wire needed for removing even the most modern windshields. Makes a difficult job easy - even on acutely angled windshields. Includes Cat. No. 87425, Braided, Golden, Windshield Cut-Out Wire; Cat. No. 87435, Starting Tool for Windshield Cut-Out Wire and Cat. No. 87440, Handles for Windshield Cut-Out Wire (Set of 2).
	87675, DOOR SPRING TOOL Use to remove and install the door hinge springs. Use this one tool to service late model General Motors cars and light trucks (with larger diameter springs). Can be used with a 1/2” open end or ratcheting box wrench.
	87810, UPHOLSTERY CLIP REMOVAL TOOL It takes only a few seconds to easily and safely remove upholstery and trim clips on doors, dashboards and consoles Just insert and pry Does not mar panel surface For plastic and metal clips on cars and trucks.
	87820, TACK PULLER Use to lift and remove upholstery and trim clips, staples, nails and brads. Comfortable, contoured handle.
	87880, 18" URETHANE CUT-OUT KNIFE Cuts the urethane bond holding windshield. Light-weight, rigid aluminum shank with vinyl grip. Also available in 24" extra long length for vehicles with extremely sloped windshields as Cat. No. 87890.
	87965, EXTRA LONG STICKER SCRAPER 16" Overall length. Specially designed to access steep, sloping windshields and other hard-to-reach places. Supplied with 5 standard steel razor blades and 1 plastic blade stored in the handle.
	89400, DOOR SKIN TOOL KIT Excellent combination kit to fold new door skins around frame Consists of Cat. Nos. 88160, Door Skin Dolly and 89350, Door Skin Hammer Door Skin Dolly absorbs shock and provides cushioning effect Door Skin Hammer easily folds the flange on door skins
	89780, COARSE NIB FILE Removes imperfections on paint jobs, such as dirt and runs, without respraying. High quality, precision ground files assure uniform results without gouging. Works on both primer coats and top coats (For use on dry paint surfaces only).
	89890, FLEXIBLE SANDING BOARD For sanding rounded or flat surfaces Uses standard cut abrasive paper 2 3/4 " x 17 1/2 " For wet or dry sanding.
	91625, PNEUMATIC PANEL CRIMPER For patching sheet metal panels uniformly and quickly. Forms a step around the area to be repaired. Patch is placed on flange of step, flush with original panel surface. Full grip handle.
	91950, 2” WIDE PNEUMATIC SCRAPER Removes gaskets, rust, undercoating and paint .401” Parker shank chisel has special extra wide 2” blade Blade has slight offset for easy use
	94540 & 94560, HOLDING PADS WITH FOUR SURFACE TREATMENT DISCS Use with air and electric tools to clean and prep surfaces. Discs install and remove easily with a quick twisting action. Flexible, flanged rubber backer pad connects to 1/4" steel shaft. Includes one Holding Pad and two each medium and coarse discs. Available in two sizes: Cat. No. 94540 is 2" and Cat. No. 94560 is 3".
	94860, 1/16" CUT-OFF WHEELS Abrasive reinforced wheels are ideal for automotive and autobody repair. Cut through clamps, hangars, sheet metal, angle iron, tubing, castings, mufflers and rusted bolts. Easier and safer to control than a torch, faster and less effort than a hacksaw.
	98350, DIAPHRAGM AIR REGULATOR For precise air regulation at the spray gun and delivers constant pressure For use with all spray guns ö conventional and HVLP Inlet is NPT Male; Outlet: NPT Female with swivel connector 22 CFM capacity; Gage ranges: 0-160 PSI and 0-11 BAR True diaphragm regulator to prevent surges and not a cheater valve Push/Pull lock to set pressure.
	98500, PNEUMATIC TOOL OILER Automatically lubricates air tools as they are being used. Ends tool burn out, stops rust and increases torque. Use on all 3/8" and 1/2" air impact guns, air wrenches, body shop air tool and pneumatic hammers. 1/4" NPT Female inlet x 1/4" NPT Male outlet.
	99000, IN-LINE WATER SEPARATOR AND AIR FILTER Removes water and foreign particles from compressed air stream. Clear reservoir shows accumulated water taken out of air line. Button release valve allows for easy disposal of accumulated liquid. 1/4" NPT Male inlet x 1/4" NPT Female outlet.
	99190, IN-LINE BLOW GUN WITH RUBBER TIP Always there, ready to use - fits permanently between air hose and coupler. No need to keep on disconnecting an air tool to hook up a blow gun.
	99300, BLOW GUN KIT Includes the most popular Blow Gun bodies and accessories. Use for blowing out tubes and pipes; directing a fine stream of air; concentrating air; accessing restricted areas and filling tires. 1/4” NPT Female inlet on Pistol Grip Handle and 1/4” NPT Female x 1/4” NPT Female inlets on Inline Blow Gun. Chrome plated nozzles.